3com AP9152 Hardware Installation Manual

3Com AP9152 802.11n 2.4/5GHz

Single-Band Access Point

Hardware Installation Guide

BOM: 3122A08W

3C Number:

3CRWE915275(FAT Mode)

3CRWE9152A75(FIT Mode)

Manual Version: 6PW102

www.3com.com

3Com Corporation

350 Campus Drive, Marlborough, MA, USA 01752

3064

English...1

Français...13

Italiano...25

Polski...37

Português Brazilian...50

Deutsch...62

Español Latino...74

Espanol...86

Regulatory Information...98

List of the Hazardous

Substances...106

documentation may be reproduced in any form or by any means or used to make any

derivative work (such as translation, transformation, or adaptation) without written

permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make

changes in content from time to time without obligation on the part of 3Com

Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition

of any kind, either implied or expressed, including, but not limited to, the implied

warranties, terms or conditions of merchantability, satisfactory quality, and fitness for

a particular purpose. 3Com may make improvements or changes in the product(s)

and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is

furnished under a license agreement included with the product as a separate

document, in the hard copy documentation, or on the removable media in a directory

file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy,

please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the

software described herein are provided to you subject to the following:

All technical data and computer software are commercial in nature and developed

solely at private expense. Software is delivered as “Commercial Computer Software”

as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as defined

in FAR 2.101(a) and as such is provided with only such rights as are provided in

3Com’s standard commercial license for the Software. Technical data is provided

with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR

52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface

any portion of any legend provided on any licensed program or documentation

contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United

States and may or may not be registered in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

All other company and product names may be trademarks of the respective

companies with which they are associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations.

To uphold our policy, we are committed to:

Establishing environmental performance standards that comply with national

legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to

recognized environmental standards. Maximizing the recyclable and reusable

content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental

standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all

end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

Environmental Statement about the Documentation

The documentation for this product is printed on paper that comes from sustainable,

managed forests; it is fully biodegradable and recyclable, and is completely

chlorine-free. The varnish is environmentally-friendly, and the inks are

vegetable-based with a low heavy-metal content.

About This Manual

Conventions

The manual uses the following conventions:

Symbols

Convention Description

Caution

Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Highlight

Means an action or information that needs special attention to

ensure successful configuration or good performance.

Note

Means a complementary description.

Obtaining Documentation

You can access the most up-to-date 3Com product documentation on the World

Wide Web at this URL: http://www.3com.com.

1

1 Product Overview

Introduction

The AP9152 is an 802.11n access point (AP) product developed by 3Com Corporation.

The AP9152 can work either as a fat AP to provide wireless access independently or as

a fit AP that operates with a wireless local area network (WLAN) switch or access

controller to provide wireless access for WLAN clients. The factory default configuration

is fat AP mode, and you can change it to fit AP mode.

Hardware Specifications

The physical dimensions and weight of the AP9152:

Physical dimensions (diameter × thickness) Weight

Φ190 × 60 mm (Φ7.48 × 2.36 in.)

Note:

Φ means diameter.

0.5 kg (1.10 lb)

The basic configurations of the AP9152:

Protocols and chassis material Internal antenna

Power

consumption

IEEE 802.11a/b/g/n,

single-RF, plastic mold design

2.4 GHz, gain: 6 dBi

5 GHz, gain: 7 dBi

5.9 W to 7 W

LEDs

Descriptions of the LEDs on the AP9152:

LED Color State Description

Steady on The power supply is normal.

POWER Green

Off

The power supply is poorly connected or is

working abnormally.

Steady on A link is present.

Off No link is present.

10/100M

(Ethernet

interface

LED)

Green

Blinking

Data is being transmitted or received at 10/100

Mbps.

Steady on A link is present.

Off No link is present.

1000M

(Ethernet

interface

LED)

Green

Blinking

Data is being transmitted or received at 1000

Mbps.

2

LED Color State Description

Off

The wireless link is not initialized or the link is

faulty.

Blinking

slowly

The wireless link is working normally.

2.4G

(Wireless

link LED)

Green

Blinking

rapidly

Data is being transmitted or received.

Off

The wireless link is not initialized or the link is

faulty.

Blinking

slowly

The wireless link is working normally.

5G

(Wireless

link LED)

Green

Blinking

rapidly

Data is being transmitted or received.

Interfaces

The AP9152 provides a console interface and an Ethernet interface.

Note: The AP9152 provides a reset button and a security slot.

Descriptions of the interfaces on the AP9152:

Interface

silkscreen

Standards and

protocols

Description

CONSOLE RS/EIA-232

The console interface is used for device

configuration and management.

Default: 9600 baud rate, 8 data bits, no parity,

one stop bit.

The default username and password for

console login are

admin

and

password

(case

sensitive) respectively

ETHERNET

IEEE802.3

IEEE802.3u

IEEE802.3af

The Ethernet interface can serve as an uplink

interface to access the Internet and as a PoE

interface at the same time.

Caution: When connecting a cable to an interface, pay attention to the interface

silkscreen to avoid connection mistakes.

2 Preparing for Installation

Unpacking and Inspection

Before unpacking the unit, make sure that the package is intact, without any sign of

damage. When unpacking the unit, avoid excessive force; otherwise, the unit inside the

package may get damaged.

After unpacking the unit, check that all items listed on the packing list are contained. If

any of the items are missing, contact your local dealer immediately.

3

Temperature and Humidity Requirements

The operating temperature and humidity requirements are as follows:

Specification Range

Operating temperature

-10°C to 55°C (14°F to 131°F)

Storage temperature

–40°C to +70°C (–40°F to +158°F)

Operating humidity (non-condensing)

5% to 95%

Power Supply

The AP9152 supports PoE power supply.

3 Installing the AP

Note:

1) Make sure that no metal particles (such as screws) fall into the Ethernet or

console interface during installation.

2) Before installing the AP9152 to the wall-mounting bracket, connect the

network cable. The network cable can only be UTP Cat-5.

3) Before connecting the console cable to the AP9152 for debugging or pressing

the reset button, you need to remove the device from the wall-mounting

bracket.

Determining the Installation Site

Determine the installation site by observing the following principles:

z Ensure that there are as few obstacles as possible between the AP and the

wireless stations.

z Keep the AP far away from electronic devices (such as microwave ovens) that

may generate RF noise.

z Ensure that the installation site will not cause any inconvenience or nuisance.

Note:

1) Make sure the ceiling is strong enough and the structure is suitable for ceiling

mounting. Reinforce the ceiling if needed.

2) Use a Kensington lock if physical security is required to protect the AP from

being stolen.

Installing the AP

The AP9152 supports three installation methods:

z Mounting the AP on a Wall

z Mounting the AP on a Ceiling

z Mounting the AP to a T-Rail

Mounting the AP on a Wall

The following describes how to mount the AP9152 on a wall:

4

z Installing the wall-mounting bracket on the wall

z Installing the AP on the wall-mounting bracket

z Locking the AP onto the wall-mounting bracket (optional)

Installing the wall-mounting bracket on the wall

Step1 Place the wall-mounting bracket tightly against the wall where the AP is to be

mounted and mark the locations to drill holes for installing the screws. Then use

a drill with a bit of 6 mm (1/4 in.) in diameter to drill holes in the wall. The hole

pattern must be identical with that in the wall-mounting bracket.

Highlight:There are five mounting holes in total in the wall-mounting bracket of the

AP9152. Select the three round holes (with a diameter of 5 mm, or 0.20 in.) for the

installation.

Figure1 Mounting hole pattern of the AP9152 wall-mounting bracket:

Step2 Insert the pointed ends of wall anchors into the drilled holes and tap the flat

ends of wall anchors with a rubber hammer until they are all flush with the wall

surface.

Step3 Align the holes in the wall-mounting bracket with the wall anchors and insert

screws through the mounting holes into the wall anchors, as shown in

Figure2.

5

Figure2 Install the wall-mounting bracket of the AP9152

(1) Drilled hole (2) Wall anchor (3) Wall-mounting bracket

(4) Key-hole clip (5) Screw

Step4 Adjust the position of the wall-mounting bracket and tighten the screws.

Note: Install the wall-mounting bracket with the arrow on the bracket pointing upwards.

Installing the AP on the wall-mounting bracket

Step1 Align the

-shaped holes on the AP’s rear panel with the key-hole clips on the

wall-mounting bracket and hang the AP on the bracket. See callout 1 in

Figure3.

Step2 Rotate the AP to fix it. See callout 2 in

Figure3. Fix the -shaped holes on the

AP’s rear panel to the key-hole clips on the wall-mounting bracket.

Figure3 Fix the AP9152 onto the wall-mounting bracket

Note: Rotating the AP9152 clockwise installs the device, while rotating it

counterclockwise uninstalls it.

Locking the AP onto the wall-mounting bracket (optional)

The AP9152 has a security slot on the upper left side, which can be used to lock the AP

6

to a fixed object to prevent theft. Follow these steps to lock the AP to a fixed object:

Step1 Fix the security cable to a nearby fixed object.

Step2 Insert the locking plate in the security slot to lock the AP.

Figure4 Lock the AP9152 to a fixed object

(2)

(3)

(1)

Before installing the security lock: (1) Security slot

(2) Security lock

After installing the security lock:

(3) Security cable

Note: The lock is user supplied.

Mounting the AP on a Ceiling

Note:

1) To use this installation method, make sure that the thickness of the ceiling is

less than 18 mm (0.71 in.), and the ceiling can bear the weight of at least 5 kg

(11.02 lb).

2) You are not recommended to use this method to mount the AP to a location

made of low-intensity materials such as a plaster ceiling. If this installation

method is required in such an environment, put a high-intensity plate beneath

the nut to secure the installation.

Select the two mounting holes of the wall-mounting bracket as shown in

Figure5 to

mount the AP on the ceiling (in mm). Follow these steps to mount the AP on the ceiling:

Step1 Drill two holes in the ceiling corresponding to the two mounting holes in the

wall-mounting bracket.

7

Figure5 Mounting holes on the wall-mounting bracket

(1) Mounting holes for mounting the AP on a ceiling

Step2 Insert the bolts through the mounting holes of the wall-mounting bracket and

the drilled holes on the ceiling, and then tighten the nuts on the other side of the

ceiling to secure the wall-mounting bracket as shown in

Figure6.

Figure6 Mount the wall-mounting bracket on the ceiling

(1) Bolt inside the ceiling (2) Washer (3) Nut

(4) Wall-mounting bracket (5) Bolt cap (6) Key-hole clip

Step3 Mount the AP9152 to the wall-mounting bracket. For details, refer to

Installing

the AP on the wall-mounting bracket.

Mounting the AP to a T-Rail

Note: The width of the T-rail must be in the range of 14 mm (0.55 in.) to 24 mm (0.94

in.).

Follow these steps to mount the AP to a T-rail:

Step1 Loosen the two M3 × 6 screws on each clip holder until the screw heads are

8

lower than the upper edge of the nuts (do not remove the screws or they may

get lost).

Step2 Adjust the T-rail clips to make the T-rail holder wider than the T-rail, and then

lock the T-rail with the T-rail holder according to the arrow.

Figure7 T-rail holder

(1) T-rail clip (2) M4 × 8 screw nut (3) M3 × 6 screw nut

(4) Clip holder (5) M4 × 8 screw (6) M3 × 6 screw

(7) Mounting hook (8) T-rail holder

(9) Before installing the AP to the T-rail, loosen the screw nuts until the screw heads are lower than the

upper edge of the nuts.

Step3 Tighten the M3 × 6 screws on the two clip holders until the screw heads touch

the T-rail, and then fix the screws.

Step4 Check that the T-rail holder is fixed to the T-rail.

Step5 Hook the mounting clip of the wall-mounting bracket to the mounting hook of

the T-rail holder, as shown

Figure8.

Step6 Insert the two M4 × 8 screws through the two holes (with a diameter of 5 mm, or

0.20 in.) on the wall-mounting bracket according to the dashed line shown in

Figure8 and fix the screws to the T-rail holder.

Step7 Check that the wall-mounting bracket is fixed to the T-rail.

Step8 Install the AP9152 to the wall-mounting bracket. For details, refer to

Installing

the AP on the wall-mounting bracket.

9

Figure8 Mount the AP to the T-rail

(1) M3 × 6 screw (2) T-rail

(3) Mounting hook (4) T-rail holder

(5) Mounting clip (6) Wall-mounting bracket

(7) Screw hole (8) M4 × 8 screw

(9) Key-hole clip (10) M4 × 8 screw

Power Supply by PoE

Power is supplied to the AP9152 through a PoE module or PoE switch. Connect one

end of an Ethernet cable to the Ethernet interface of the AP9152 and the other end to

an Ethernet interface of the PoE device.

Caution: Identify the mark on the device to avoid taking the console interface for the

Ethernet interface, or vice versa.

4 Connecting the AP(FAT AP)

On a Network with a DHCP Server

The DHCP server automatically assigns an IP address to the AP.

To find the address, either get it from the DHCP Server, or enter the following command

at the CLI interface:

<9152> display vlan 1

10

On a Network Without Any DHCP Server

The AP uses the default factory configuration that includes the following information.

z The default IP address of the AP is 192.168.0.50.

z The AP has the Telnet server enabled by default. The default authentication

username and password are admin, and password respectively (case

sensitive). You can remotely manage and maintain the AP through Telnet.

Logging In to the AP (FAT AP)

To log in to the AP that has an IP address configured, follow these steps:

1) Connect the AP to a PC, and ensure that the PC and AP can communicate

with each other properly.

2) Launch a web browser. In the address bar, type your AP’s IP address and

press Enter.

3) At the AP login interface, type the username, password, and the verification

code, select the language (English and Chinese are supported at present),

and click Login. The default username and password are case-sensitive:

z Username: admin

z Password: password

Converting a FAT AP to a FIT AP

If you want to change a fat AP to a fit AP, go to the web page http://www.3com.com to

get the instructions.

5 Approved Channels

The operating channels of the AP vary with countries. Select your country from the

country-selection list.

To conform to FCC , Canada, EU and other country-specific restrictions, the AP may

have shipped with channel restrictions for your country. Please visit the 3Com web site

for the latest software version. Appendix A lists the Software Downloads information.

11

A Obtaining Support for your Product

Register Your Product

Warranty and other service benefits start from the date of purchase, so it is important to

register your product quickly to ensure you get full use of the warranty and other service

benefits available to you.

Warranty and other service benefits are enabled through product registration. Register

your product at http://eSupport.3com.com/. 3Com eSupport services are based on

accounts that you create or have authorization to access. First time users must apply

for a user name and password that provides access to a number of eSupport features

including Product Registration, Repair Services, and Service Request. If you have

trouble registering your product, please contact 3Com Global Services for assistance.

Purchase Value-Added Services

To enhance response times or extend warranty benefits, contact 3Com or your

authorized 3Com reseller. Value-added services like 3Com Express

SM

and Guardian

SM

can include 24x7 telephone technical support, software upgrades, onsite assistance or

advance hardware replacement. Experienced engineers are available to manage your

installation with minimal disruption to your network. Expert assessment and

implementation services are offered to fill resource gaps and ensure the success of

your networking projects. More information on 3Com maintenance and Professional

Services is available at http://www.3com.com/

Contact your authorized 3Com reseller or 3Com for a complete list of the value-added

services available in your area.

Troubleshoot Online

You will find support tools posted on the 3Com web site at http://www.3com.com/

3Com Knowledgebase helps you troubleshoot 3Com products. This query-based

interactive tool is located at http://knowledgebase.3com.com and contains thousands

of technical solutions written by 3Com support engineers.

Access Software Downloads

Software Updates are the bug fix / maintenance releases for the version of software

initially purchased with the product. In order to access these Software Updates you

must first register your product on the 3Com web site at http://eSupport.3com.com/

First time users will need to apply for a user name and password. A link to software

downloads can be found at http://eSupport.3com.com/, or under the Product Support

heading at http://www.3com.com/

Software Upgrades are the software releases that follow the software version included

with your original product. In order to access upgrades and related documentation you

must first purchase a service contract from 3Com or your reseller.

12

Telephone Technical Support and Repair

To enable telephone support and other service benefits, you must first register your

product at http://eSupport.3com.com/

Warranty and other service benefits start from the date of purchase, so it is important to

register your product quickly to ensure you get full use of the warranty and other service

benefits available to you.

When you contact 3Com for assistance, please have the following information ready:

z Product model name, part number, and serial number

z Proof of purchase, if you have not pre-registered your product

z A list of system hardware and software, including revision level

z Diagnostic error messages

z Details about recent configuration changes, if applicable

To send a product directly to 3Com for repair, you must first obtain a return authorization

number (RMA). Products sent to 3Com, without authorization numbers clearly marked

on the outside of the package, will be returned to the sender unopened, at the sender’s

expense. If your product is registered and under warranty, you can obtain an RMA

number online at http://eSupport.3com.com/. First time users will need to apply for a

user name and password.

Contact Us

3Com offers telephone, e-mail and internet access to technical support and repair

services. To access these services for your region, use the appropriate telephone

number, URL or e-mail address.

Find a current directory of contact information posted on the 3Com web site at

http://csoweb4.3com.com/contactus/.

13

1 Présentation du produit

Introduction

Le modèle AP9152 est un dispositif de point d'accès 802.11n (PA) développé par 3Com

Corporation. Le modèle AP9152 peut fonctionner soit en tant que PA autonome, dit «

fat », et fournir ainsi un accès sans fil indépendant, soit en tant que PA partiellement

allégé, dit « fit », fonctionnant avec un commutateur de réseau sans fil (WLAN) ou un

contrôleur d'accès, afin de fournir un accès sans fil aux clients WLAN. Le mode de

configuration d'usine (par défaut) est « PA autonome », mais vous pouvez passer en

mode « PA partiellement allégé ».

Spécifications matérielles

Dimensions physiques et poids du modèle AP9152:

Dimensions physiques (diamètre × épaisseur) Poids

Φ190 × 60 mm (Φ7,48 × 2,36'')

Remarque :

Φ signifie diamètre.

0,5 kg (1,10 lb)

Configuration de base du modèle AP9152 :

Protocoles et matériel du

châssis

Antenne interne

Consommation

électrique

IEEE 802.11a/b/g/n,

RF unique, moulage de matières

plastiques

2,4 GHz, gain : 6 dBi

5 GHz, gain : 7 dBi

De 5,9 W à 7 W

Indications lumineuses

Description des indications lumineuses du modèle AP9152 :

Indications

lumineuses

Couleur Etat Description

Fixe L'alimentation électrique est normale.

POWER Vert

Eteint

L'alimentation électrique est mal connectée

ou fonctionne de manière anormale.

Fixe La connexion est effective.

Eteint La connexion n'est pas effective.

10/100M

(Indication

lumineuse

Ethernet)

Vert

Clignote

Les données sont transmises ou reçues à

10/100 Mbps.

Fixe La connexion est effective.

Eteint La connexion n'est pas effective.

1000M

(Indication

lumineuse

de l'interface

Ethernet)

Vert

Clignote

Les données sont transmises ou reçues à

1000 Mbps.

14

Indications

lumineuses

Couleur Etat Description

Eteint

La connexion sans fil n'est pas initialisée ou

est défectueuse.

Clignote

lentement

La connexion sans fil fonctionne

normalement.

2,4G

(Indication

lumineuse

de la

connexion

sans fil)

Vert

Clignote

rapidement

Les données sont transmises ou reçues.

Eteint

La connexion sans fil n'est pas initialisée ou

est défectueuse.

Clignote

lentement

La connexion sans fil fonctionne

normalement.

5G

(Indication

lumineuse

de la

connexion

sans fil)

Vert

Clignote

rapidement

Les données sont transmises ou reçues.

Interfaces

Le modèle AP9152 est doté d'une interface de console et d'une interface Ethernet.

Remarque : Le modèle AP9152 est doté d'un bouton Reset et d'une encoche de

sécurité.

Description des interfaces du modèle AP9152 :

Ecrans

d'interface

Normes et

protocoles

Description

CONSOLE RS/EIA-232

L'interface de la console permet de configurer et

de gérer l'appareil.

Par défaut : Fréquence de baud de 9600, 8 bits

de données, aucune parité, un bit d'arrêt.

Le nom d'utilisateur et le mot de passe par défaut

associés à l'ouverture de session dans la console

sont respectivement

admin

et

password

(sensible à la casse)

ETHERNET

IEEE802.3

IEEE802.3u

IEEE802.3af

L'interface Ethernet peut servir d'interface Uplink

et d'interface PoE en même temps.

Attention : Quand vous connectez un câble à une interface, veillez à une pas faire

d'erreurs de connexion en observant bien l'écran.

2 Préparation de l'installation

Déballage et inspection

Avant de déballer l'unité, vérifiez que l'emballage est intact, sans aucun signe de

dommage. Evitez de forcer lors du déballage, au risque d'endommager l'unité.

15

Une fois l'unité déballée, vérifiez la présence de toutes les pièces indiquées sur

l'emballage. Contactez immédiatement votre revendeur local en cas de pièce

manquante.

Exigences relatives à la température et à humidité

Les exigences relatives à la température et à humidité sont les suivantes :

Spécification Plage

Température de fonctionnement De -10°C à 55°C (de 14°F à 131°F)

Température de stockage De –40°C à +70°C (de –40°F à +158°F)

Humidité relative (sans condensation) De 5% à 95%

Alimentation électrique

Le modèle AP9152 est compatible avec une alimentation électrique PoE.

3 Installation du PA

Remarque :

1) Vérifiez qu'aucune particule métallique (comme des vis) ne tombe dans

l'interface Ethernet ou l'interface de la console durant l'installation.

2) Avant d'installer le modèle AP9152 sur le support de montage mural,

connectez le câble réseau. Le modèle du câble réseau ne peut être que UTP

Cat-5.

3) Avant de connecter le câble de la console au modèle AP9152 pour effectuer

le débogage ou appuyer sur le bouton Reset, vous devez ôter le dispositif du

support de montage mural.

Déterminer le site d'installation

Pour déterminer le site d'installation, suivez les principes ci-après :

z Vérifiez qu'il y ait le moins d'obstacles possible entre le PA et les stations sans

fil.

z Eloignez le PA de tout dispositif électronique (comme les fours à micro-ondes)

pouvant générer des interférences par radiofréquence.

z Vérifiez que le site d'installation ne cause pas d'inconvénient ni de nuisance.

Remarque :

1) Vérifiez la solidité du plafond. La structure doit convenir à un montage au

plafond. Renforcez le plafond si nécessaire.

2) Si vous devez installer une sécurité physique, utilisez un verrou Kensington

afin de protéger le PA des vols.

Installation du PA

Le modèle AP9152 permet trois modes d'installation.

z Montage du PA sur un mur

16

z Montage du PA sur un plafond

z Montage du PA sur un rail en T

Montage du PA sur un mur

Les informations suivantes décrivent comment installer le modèle AP9152 sur un mur :

z Installation du support de montage mural sur le mur

z Installation du PA sur le support de montage mural

z Verrouillage du PA sur le support de montage mural (en option)

Installation du support de montage mural sur le mur

Etape 1 Plaquez le support de montage mural fermement contre le mur où le PA doit

être monté et marquez les emplacements à percer afin d'installer les vis.

Utilisez ensuite un foret de 6 mm (1/4'') de diamètre afin de percer les trous

dans le mur. L'écartement des trous doit être identique à celui du support de

montage mural.

Précisions :Le support de montage mural du modèle AP9152 comporte cinq trous de

montage au total. Les trois trous ronds (diamètre de 5 mm ou 0,20'') servent à

l'installation.

Figure 1 Ecartement des trous du support de montage mural du modèle AP9152 :

Etape 2 Insérez les extrémités en pointe des points d'encrage muraux dans les trous

percés et enfoncez leur partie plate avec un marteau jusqu'à ce qu'ils

arrivent au ras du mur.

Etape 3 Alignez les trous du support de montage mural avec les points d'encrage et

insérez les vis par les trous de montage dans les points d'encrage, comme

indiqué sur la Figure2.

17

Figure 2 Installation du support de montage mural du modèle AP9152

(1) Trou percé (2) Point d'encrage (3) Support de montage mural

(4) Clip de trou de serrure (5) Vis

Etape 4 Ajustez la position du support de montage mural et serrez les vis.

Remarque : Installez le support de montage mural de sorte que la flèche pointe vers le

haut.

Installation du PA sur le support de montage mural

Etape 1 Alignez les trous en forme de

du panneau arrière du PA avec les clips de

trou de serrure du support de montage mural, puis accrochez le PA sur le

support. Voir le numéro 1 sur la Figure3.

Etape 2 Faites tourner le PA afin de le fixer. Voir le numéro 2 sur la Figure3. Fixez les

trous en forme de

du panneau arrière du PA aux clips de trou de serrure

du support de montage mural.

Figure 3 Fixation du modèle AP9152 sur le support de montage mural

Remarque : Faites tourner le modèle AP9152 dans le sens des aiguilles d'une montre

pour installer l'appareil et dans le sens contraire pour l'ôter.

A página está carregando ...

3com AP9152 Hardware Installation Manual

3com AP9152 Hardware Installation Manual

em outros idiomas

Artigos relacionados

Outros documentos